Physical Sciences and Mathematics Commons^™

Preparation Of Silica-Coated Lanthanum-Strontium Manganite Particles With Designable Curie Point, For Application In Hyperthermia Treatments, Vuk Uskoković, Aljoša Košak, Miha Drofenik

Pharmacy Faculty Articles and Research

Silica-coated lanthanum–strontium manganite particles with La_0.76Sr_0.24MnO_3+δ stoichiometric formula, exhibiting Curie temperature at ∼40°C, were prepared by using a traditional solid-state method of synthesis of magnetic ceramic particles, followed by milling and a low-temperature coating procedure in an aqueous alcoholic alkali medium. The properties of the obtained material establish it as a potential candidate for self-regulated power-absorbing and temperature-controlling materials in hyperthermia treatments. Moreover, core-comprising LaSr–manganites with different stoichiometries, ranging from La_0.5Sr_0.5MnO_3+δ to LaMnO_3+δ, were synthesized, with magnetic and structural properties examined thereof. Herein reported findings can potentially be …

Nmr Studies Of Escherichia Coli Acyl Carrier Protein: Dynamic And Structural Differences Of The Apo- And Holo-Forms, Yangmee Kim, Evgueni Kovriguine, Ziad Eletr

Chemistry Faculty Research and Publications

Two indicators of conformational variability of Escherichia coli acyl carrier protein (ACP) have been investigated, namely backbone dynamics and chemical shift variations of ACP. Hydrophobic interactions between the 4′-PP prosthetic group and the hydrophobic pocket enclosed by the amphipathic helices resulted in chemical shift perturbations in the residues near the prosthetic group binding sites and contact sites in the hydrophobic pockets upon conversion from apo- to holo-forms. At pH 7.9, destabilization of ACP due to negative charge repulsions and the deprotonated state of His 75 resulted in observed chemical shift changes in the C-terminal region. Model-free analysis showed that the …

Orientational Disorder In Sodium Cadmium Trifluoride Trihydrate, Nacdf3·3h2o, Robert W. Smith, Arthur Mar, Jianjun Liu, Stan Schnell, John R. Hardy

Chemistry Faculty Publications

Attempts to synthesize the hypothetical anhydrous fluoroperovskite NaCdF₃, which has been predicted to be stable, resulted instead in a hydrated fluoride of nominal composition NaCdF₃·3H₂O. It decomposes to sodium fluoride, cadmium fluoride, and water at 60 °C. Its structure has been determined by single-crystal X-ray diffraction. Na_0.92(2)Cd_1.08F_3.08·2.92H₂O crystallizes in the cubic space group with a = 8.2369(4) Å and Z = 4. The structure is based on the NaSbF₆-type (an ordered variant of the ReO₃-type) and features tilted sodium- and cadmium-centred octahedra …

The Electrochemical Separation Of Curium And Americium: Quaterly Report January - March, 2006, David W. Hatchett, Kenneth Czerwinski

Separations Campaign (TRP)

This research report outlines the current status and progress associated with the electrochemical separation of Curium and Americium. For two and a half years, research has been actively performed on this project, and is currently on schedule for the proposed timelines.

Progress:

• The electrochemical characterization of Ce and Eu complexed with EDTA, NTA, and Citrate has been completed.

• Synthesis of the polymer substrate and the chelating ligand is underway. Approximately 50 grams of disulfide has been produced to produce the chelating thiol group required for the last set of studies.

• Gold substrates have been prepared to perform …

Flammability Of Styrenic Polymer Clay Nanocomposites Based On A Methyl Methacrylate Oligomerically-Modified Clay, Xiaoxia Zheng, David D. Jiang, Dongyan Wang, Charles A. Wilkie

Chemistry Faculty Research and Publications

Nanocomposites of polystyrene, high impact polystyrene, acrylonitrile–butadiene–styrene terpolymer, polypropylene, and polyethylene were prepared using a methyl methacrylate oligomerically-modified clay by melt blending and the thermal stability and fire retardancy were studied. These nanocomposites were characterized by X-ray diffraction, transmission electron microscopy, thermogravimetric analysis and cone calorimetry. The results show a mixed morphology, depending on the polymer.

Kinetic And Spectroscopic Characterization Of The E134a- And E134d-Altered Dape-Encoded N-Succinyl-L,L-Diaminopimelic Acid Desuccinylase From Haemophilus Influenzae, Ryan S. Davis, David L. Bienvenue, Sabina I. Swierczek, Danuta M. Gilner, Lakshman Rajagopal, Brian Bennett, Richard C. Holz

Physics Faculty Research and Publications

Glutamate-134 (E134) is proposed to act as the general acid/base during the hydrolysis reaction catalyzed by the dapE-encoded N-succinyl-l,l-diaminopimelic acid desuccinylase (DapE) from Haemophilus influenzae. To date, no direct evidence has been reported for the role of E134 during catalytic turnover by DapE. In order to elucidate the catalytic role of E134, altered DapE enzymes were prepared in which E134 was substituted with an alanine and an aspartate residue. The Michaelis constant (K _m) does not change upon substitution with aspartate but the rate of the reaction changes drastically in the following order: glutamate (100% …

Applications Of Acoustic Wave Devices For Sensing In Liquid Environments, Jeanne Hossenlopp

Chemistry Faculty Research and Publications

Acoustic wave devices such as thickness shear mode (TSM) resonators and shear horizontal surface acoustic wave (SH-SAW) devices can be utilized for characterizing physical properties of liquids and for chemical sensor applications. Basic device configurations are reviewed and the relationships between experimental observables (frequency shifts and attenuation) and physical properties of liquids are presented. Examples of physical property (density and viscosity) determination and also of chemical sensing are presented for a variety of liquid phase applications. Applications of TSMs and polymer-coated guided SH-SAWs for chemical sensing and uncoated SH-SAWs for “electronic tongue” applications are also discussed.

Electrochemistry And Structures Of Silicon Surface, Gregory X.Zhang

Journal of Electrochemistry

Accurate control and fabrication of silicon surface structures from atomic scale to micrometer scale,which may be randomly associated with surface roughness or have well defined patterns,is critical for the per-formance and reliability of electronic devices.Electrochemical reactions of silicon in solutions involved in wetcleaning and etching of silicon wafer play an importantrole in determining the structures of silicon surface.Atre-mendous amount of researches have been done in the last several decades to understand and control a range ofcomplex electrochemical reactions at silicon/solution interface and their relations to the resulted surface struc-tures.The findings generated from these research efforts have been compiled and integrated …

Development On Hydriding/Dehydriding Kinetics Of Mg Nano-Materials For Hydrogen Storage, Wei Mo, Hong-Liang Sun, Hai-Chang Zhang, Hua-Bin Yang, Zuo-Xiang Zhou

Journal of Electrochemistry

The development of Mg nano-materials for hydrogen storage in the recent decade has been reviewed in this paper.It was shown the Mg nano-powders prepared by high-energy ball milling showed promising hydriding and dehydriding performance with the transition metal oxides and other types of hydrogen storage alloys(ABx)as the catalysts.

Electrocatalytic Oxidation Of Glucose On Nano Pt/C Electrode, Cui-Lian Chen

Journal of Electrochemistry

Nano Pt/C electrocatalysts were prepared by intermittent microwave heating method.The electrooxidation of glucose on smooth Pt and～Pt/C electrodes has been studied and compared.The results showed that the electrochemical properties on nano Pt/C were improved due to the reduction of the overpotential and the increase in the kinetic rate.The surface area would be significantly increased when the particle size of the catalyst was reduced to nano-scale,resulting in the increase in the activity.The enhancement in the resistance to poisoning could be explained that the oxygen-containing species are easier to react with poisoning species on nano Pt/C and re-active the electrode.

Electro-Generated Feo_4~(2-) Using Modified Chitosan Cation Exchange Membrane, Huai-Zhen Zhong, Ri-Yao Chen, Xi Zheng, Zhen Chen

Journal of Electrochemistry

The chitosan cation membrane was prepared by crosslinked 2% and doped with 1% H_(2)SO_(4).The products were marked as MCS.The physical properties and the ion exchange capacity of MCS were studied.Compared to the non-modified membrane,it was found that chemical modifications contributed to improving ion exchange capacity from 0.25 to 2.09 meq/g.Results was also suggested that the MCS can be used as a separator when producing sodium ferrate flocculent using electrochemical process.

Studies On Pva-Cmc-Koh-H_2o Alkaline Polymer Electrolytes, An-Bao Yuan

Journal of Electrochemistry

A given amount of sodium carboxymethyl cellulose(CMC)was added to PVA complex and thus the PVA-CMC-KOH-H_(2)O alkaline polymer electrolyte with this modification was prepared.The properties of the polymer electrolyte films were characterized by AC impedance,cyclic voltammetry,differential thermal analysis and infrared spectroscopic analysis methods.The polymer electrolyte exhibited a high ionic conductivity,typically 10~(-2)S·cm~(-1) with an electrochemical stability window of about 1.6 V on stainless steel blocking electrodes.The influence of the film composition such as KOH,H_(2)O and CMC on ion conductivity was investigated.In addition,a preliminary study was carried out on the polymer electrolyte for Ni/MH battery.It was shown that the Ni/MH battery with the …

Anodic Behaviors Of Pb-Ca-Sn-Re Alloy And Tradditional Pb-Ca-Sn Alloy In Sulfuric Acid Solutions, Dang-Guo Li, Gen-Shu Zhou

Journal of Electrochemistry

The anodic behaviors of Pb-Ca-Sn-Re and Pb-Ca-Sn alloys were investigated at 1.28 V(vsHg/(H_2SO_(4))) in 4.5 mol/L sulfuric acid solution by means of ac voltammetry,ac impedance and cyclic voltammetry.The results showed that the corrosion-resistance property of Pb-Ca-Sn-Re alloy is better than that of tradditional Pb-Ca-Sn alloy,the growth of Pb(Ⅱ) compounds was inhibited in the film of Pb-Ca-Sn-Re alloy,and the film impedance of Pb-Ca-Sn-Re alloy was decreased,indicating that the conductivity of the film was(increased),which is helpful to enhance the deep recycling property for lead acid battery.

Degradation Of Aniline Wastewater By Electro-Heterogeneous Catalysis Reactor, Wei-Li Liu

Journal of Electrochemistry

The treatment of aniline wastewater was investigated using novel electro-heterogeneous catalysis reactor.The effects of applied cell voltage,electrolysis lime,pH value and the electrolyte on electrolysis were investigated.The experimental results show that the reactor with a cell voltage of 30 V,an electrolysis time of 1 h,pH value of 7 and a salinity of 800 mg/L can achieve the best removal efficiency on aniline,which is more efficient than the sole electrochemical reactor.

The Complex Of Pasp And Tungstate As Inhibitors Of Cupronickel B10′S Corrosion In 3% Nacl Solution, Qun-Jie Xu

Journal of Electrochemistry

AC impedance and polarization curve measurements were conducted to study the effects of environ-ment-friendly inhibitors PASP,Na_(2)WO_(4)and their complexes on the corrosion of cupronickel B10 in 3%NaCl solution.The results indicate that PASP or Na_(2)WO_(4)alone does inhibit the corrosion of B10,and most effectiveconcentrations are 40 mg/L and 60 mg/L for PASP and Na_(2)WO_(4),respectively.With the total concentration of 40mg/L for the complex inhibitors,the optimum complex ratio of PASP to Na_(2)WO_(4)was 3:1.The complex of such a combination showed a significantly synergetic inhibition effect on the corrosion of B10.

Effect Of Applied Potentials On The Formation Of Self-Assembled Monolayers Of Alkanethiol, Diao Peng

Journal of Electrochemistry

The self-assembled monolayers(SAMs)of n-dodecanethiol were prepared on gold substrates under electrochemical conditions using potential step technique.Electrochemical impedance spectroscopy was employed to characterize the SAMs prepared under different substrate potentials.It is found that the potential applied to gold substrate has great influence on the formation of SAMs.Within potential regime-0.8 V to 1.2 V,the increase of applied potential firstly leads to the formation of SAMs with higher packing density,better ordering and less defects.However,after reaching the maximum at 0.4 V,the packing density and the ordering of SAMs begin to deteriorate when the substrate potential is further increased.This work provides solid experimental basis for …

Oxygen Enrichment Effect Of Ceo_2 To The Cathode Performance Of Proton Exchange Membrane Fuel Cell, Xiang-Li Hou, Hong-Feng Xu, Jian-Hua Dong, Xin Sun

Journal of Electrochemistry

CeO_2 was added to Pt/C catalyst in the cathode of PEMFC by both sol and impregnation methods.The samples were evaluated by TEM,cyclic voltammogram techniques and proton exchange membrane fuel cell performance test.The addition of CeO_2 obviously improved the performance of PEMFC and represented a notable function of oxygen enrichment in the cathode side.But with the addition of CeO_2,part of the catalyst surface was covered and led to the performance drop of the PEMFC.The best content of CeO_2 is 1% when it is added by impregnation method and 3% when it is added by sol method.

Effects Of Srb Biofilm And Corrosion Product Films On Corrosion Behavior Of Carbon Steel, Jing Lin

Journal of Electrochemistry

Electrochemical techniques and surface analysis techniques were applied to study corrosion characteristic of A3 steel.The effects on corrosion behavior of A3 steel by sulfate-reducing bacteria(SRB)(biotic media)and corrosion product(abiotic media)were studied.The results showed that biofilms and corrosion product films play different role during different stages.Biofilms were easier flaky with increasing of its thickness.Non-uniform biofilms reduced pitting corrosion of the specimens.The corrosion product films formed under abiotic conditions were more adherently to the surface of the metal than those formed in biogenic media.

In-Situ Detection Of The Effect Of Brighter In The Solution For Nickel And Phosphor Alloy, Jian Zheng, Ning Li, De-Yu Li, Guo-Feng Cui

Journal of Electrochemistry

In this work,the gold-plated mica was used for the substrate,the concentration of 5% of normal plating solution for the nickel was used as the mother solution,and the effect for the deposition by the brighter with ECSTM was in-situ detected.The solution for deposition without the brighter has no brightness,though the values of the roughness and the H_(A-V) have reduced in evidence after deposition;the solution for deposition with the complete brighter although has great brightness,the values of the roughness and the H_(A-V) have increased(after) deposition;the solution for deposition with the half brighter has a moderate effect on the H_(A-V) and (brightness).Hence,the brighter …

2006 National Conference On Corrosion Electrochemistry And Measuring Methods

Journal of Electrochemistry

No abstract provided.

25th Ccs Congress (Notes Of The First Circular)

Journal of Electrochemistry

No abstract provided.

Potential Distributions On External Tank Bottom Under Cathodic Protection Of Deep Well Anode, Yan-Xia Du, Guo-Zhong Zhang, Gang Liu

Journal of Electrochemistry

Potential distributions of deep well anodic electric field on external tank bottom were derived according to the basic law of electromagnetic field and the geometry characteristics of cathodic protection system.Making use of electric field superposition principle,considering the action of anodic and cathodic electric fields,the potential distributions on external tank bottom under the protection of deep well anode were studied.The calculated results were compared and agred well with the measured data.

Special Photoelectrochemical Response Of Nano-Crystalline Tio_2 Electrode, Bi-Bo Lan, Jian-Zhang Zhou, Yan-Yan Xi, Hong-Xiang Chen, Guang-Hua Yao, Zhong-Hua Lin

Journal of Electrochemistry

The nano-crystalline TiO_2 electrodes were prepared by spread method,electrodeposition and sol-gel method.The experimental results show that the nano-crystalline TiO_2 electrodes have special photoelectrochemical response-the photocrrent-potential curves appear peaks.The special photoelectrochemical behaviors of nano-(crystalline) TiO_2 electrodes are ascribed to nano-structure as well as special light induced redox reaction mechanism of nano-crystalline semiconductor electrodes.

Electroless Nickel Plating On Carbon Nanotube With Non-Palladium Activation Procedure, Guang-Hui Hu, Hui-Huang Wu, Yangfang-Zu Yangfang-Zu

Journal of Electrochemistry

A new procedure of surface activation without using palladium salt was proposed for electroless nickel plating on carbon nanotubes.In the procedure,carbon nanotubes were oxidized by nitric acid and then neutralized with NaOH to create carboxyl surface groups which were used to adsorb Ni~(2+)ions,thereafter the adsorbed Ni~(2+)ions were chemically reduced into Ni nano-particles as a catalytic center for electroless nickel deposition,all these were further confirmed by infrared absorption spectra and electron microscopic observations.The results indicate that the procedure is feasible to electroless nickel plating on carbon nanotubes.The different morphology of deposits obtained from electroless plating was also discussed.

Conductivity Of Comb Polyether Pure Solid Polymer Electrolyte, Lin Ye

Journal of Electrochemistry

A comb polymer was synthesized through cationic ring-opening polymerization starting from a monomer 3-hydroxymethyl-3-methyl-oxetane.The ion conductivity was measured by CHI660A electrochemical station under various lithium salt concentrations and various temperatures.The highest ion conductivity was recorded to be 10~(-4.43)S/cm at room temperature and 10~(-3.44)S/cm at 80 ℃.DSC results showed that the segment moves more difficultly with the increasing of lithium salts concentration.XPS found the existence of aggregating lithium ions in POE5 and POE10,and it suggested that POE20 had a suitable lithium concentration for polymer electrolyte.

Effects Of Sulfide Ions On The Inhibiting Efficiency Of Eda As A Copper Corrosion Inhibitor In Dilute Hcl Solution, Wen-Juan Qu, Rong-Gui Du

Journal of Electrochemistry

The anticorrosion action of EDA on copper in dilute HCl solution and the effect of sulfide ions on the inhibiting efficiency were studied by the Tafel plot method.The corrosion potential of Cu shifted to more positive value and the corrosion current density decreased after the addition of Na_(2)S to the solution.The results indicated that sulphide ions could increase the inhibiting efficiency of EDA because of the synergistic inhibition effect between EDA and Na_2S,resulting from the adsorption of HS~(-)on the surface of Cu,facilitated the adsorption of EDA to form a highly protective adsorbed layer which prevented Cu from corrosion.

The Effect Of Solution Concentration On Properties Of Ru-Ti-Ir Oxide Anode Coatings, Wang Ke

Journal of Electrochemistry

The anode coatings of Ru-Ti-Ir oxide with various solution concentrations were prepared by thermal decomposition.The scanning electron microscope(SEM),energy dispersive X-ray detector(EDX),X-ray diffraction(XRD),accelerated life,polarization curve,cyclic voltammetry and electrochemical impedance.spectroscopy(EIS)tests were carried out.The results showed that there was an obvious effect of solution concentrations on the morphology of the coatings,but little effect on polarization of chlorine evolution.Voltammetric charges and double layer capacitances of anode coatings had a tendency to fall down firstly then increase afterwards as the solution concentration increased.

Electrochemical Reduction Behavior Of Benzaldehyde In The Ionic Liquids, Ning Zhao, Wen-Ju Dong

Journal of Electrochemistry

In this paper,the electrochemical reduction of benzaldehyde was investigated in C_4MIMBF_(4)、(C_(6)MIMBF_(4)) and C_(8)MIMBF_(4) ionic liquids by cyclic linear sweep voltammetry,cyclic square-wave voltammetry and chronocoulometry.Benzaldehyde exhibits two successive one-electron irreversible reduction(E_(P1)=-1.39 V,E_(P2)=1.69 V) with GC electrode in C_(4)MIMBF_(4),the voltammetric data for benzaldehyde give diffusion coefficients of 1.5 10~(-8)cm~(2)/s and 1.3 10~(8)cm~2/s.There is one current peak in C_(6)MIMBF_(4)and C_8MIMBF_4 ionic liquids due to their stronger alkalinity then C_4MIMBF_4.The decay time of the charging current became longer in C_(4)MIMBF_(4)、C_(6)MIMBF_(4)、C_(8)MIMBF_(4),and slower heterogeneous kinetics in(C_(6)MIMBF_(4)) and C_(8)MIMBF_(4) ionic liquids.

Mechanism Of Self Discharge Performance Improvement In The Ni-Mh Batteries With Naoh Electrolyte, Xiao-Feng Li

Journal of Electrochemistry

The self-discharge performance and charge efficiency at 60 ℃ for Ni-MH battery can be markedly enhanced by using NaOH electrolyte instead of KOH electrolyte.Both the results of electrochemical impedance spectroscopy and cyclic voltammetry tests indicate that the separation of H_2 from the negative electrode may be partly blocked in the former because of the change of the adsorption/desorption behavior of H on the surface of the negative electrode,thus results in an improvement of self-discharge performance of the battery.

Preparation Of Spinel Limn_2o_4 Cathode Materials For Li-Ion Batteries Based On Sol-Gel Process, Xiang-Ming He

Journal of Electrochemistry

Spinel LiMn_(2)O_(4) was prepared from CH_(3)COOLi·2H_(2)O,Mn(CH_(3)COO)_(2) and adipic acid based on sol-gel process.XRD analysis showed that when the sintering temperature increased,the crystallinity increased,and the capacity also increased.However,its cycleability reached a maximum value at 750 ℃.The sintering duration also influenced on the capacity.The optimized performance was obtained when the sintering was carried out at 750 ℃ for 20 h.Under these conditions,as-prepared spinel LiMn_(2)O_(4) presented the initial discharge capacity of 130 mAh g~(-1) and 125 mAh g~(-1) at 15~(th) cycle.